Finally Finished 1780's Stays!

Well, here they are!  I finished my new back- and front-lacing 1780's stays last week.  The pattern fits very well, and they are surprisingly comfortable most of the time.  They were originally intended to have straps, and they may one day, but I like them as they are for now (even with the little stubs, they don't get in the way that much though).  The chanels are all machine sewn, except for the first channel I did, which made me decide to use the machine!  The binding and eyelets are handsewn, however. 

Materials:

Top layer- Linen

Middle layer- Denim

Inside layer- Cotton muslin

Boning- Thin cable ties (Strategically placed, and they are definitely enough for my figure.  I tried a few larger ones, but I had issues with them twisting in the channels.  The boning was placed between the 2 inside layers, because it showed under just the top layer)

You can see how the stays have already conformed to my figure a little bit.  I have worn them for about 7-10 hours so far.

And a few shots of the inside...

I didn't take many in-progress shots, because I was sewing like mad to get them done so I could start some other projects.

Testing out the channel width and boning choice.

The two front panels, which were lonely for a few months until I felt like sewing the rest of them.

I hope you enjoyed seeing them!

Rebecca

Working, working...

I apologize for not having posted in so long.  The reason is that I've been sewing like crazy!  In the past few days, I have finished my 18th century stays and started a new linen round gown.  I will be working on photographing the stays as soon as I can, and the gown once it is done.  I'm trying to finish it in time for an event next weekend, we'll see how that goes...

Rebecca
(PS:  For some reason, my fabric for the Sacque back dress has still not arrived!  I'm not sure what to do about it, I've already called Joann's.)

How to Scale Up a Pattern the Easier Way!

In this post, I'm going to show you the way I scale up gridded patterns.  This is the method I used to make the pattern for the waistcoat, as shown.

(Warning: There is some geometry involved here, as in all pattern scaling, I've just tried to make it as easy as possible to understand)

What you need: A gridded pattern, a ruler, a pen or pencil, lots of scrap paper, an iron, tape.

Step 1:  Trace your necassary pattern pieces on a piece of paper. It doesn't have to be notebook paper, but it hepls you keep a straight line.  Then look at the scale on the pattern (in this case, I think it was 1 square equals 3 inches, we will call the side of the square N, to make the instructions simpler) and draw a grid according to that scale.  If your grid is not correct, the final pattern will either be too big or too small.

Step 2:  Prepare your pattern paper.  This can be any type of thicker paper you want. It's is a very good chance for recycling!  It is preferable to iron it on low heat and get all the wrinkles out.  It works like magic!

Step 3:  On your pattern paper, begin to form a grid.  If your paper has a 90 degree corner, it is easy to start, mark a spot N in. from the bottom of the paper on both sides and in the middle.  If your paper does not have a corner but has a straight bottom edge, measure N away from the bottom at a 90 degree angle and mark it in at least 3 places.  If you have a randomly shaped piece of paper, make a fold near the bottom or draw a line and use it as your bottom edge.

However, instead of drawing lines for the grid (which is very time-consuming), fold the paper like a fan where you would draw the line.  Run a ruler or something heavy and flat over the crease to set it in (I do not recommend using an iron at this stage, because it will get rid of all of the creases).

Continue folding, like a fan.

Once you finish going one way, start the folds going the other way, to form the grid.  The folds should be the same depth (N) going both ways, because the grid needs to be a square. 

Step 4:  Begin scaling up your pattern.  You use the creases you made to guide you, and the good thing about this method is that it takes much less time than actually drawing out a grid.  You also don't have a bunch of pencil lines going across your pattern piece.

After scaling it up, cut it out!

The finished pattern:

Front

Back

Hopefully this helps you have some more sewing creations flying off the needle this summer.  Best wishes!

Rebecca